One of the many reasons stormwater drains are crucial is that they aid in the cleanup of precipitation and runoff from parking lots and roadways. However, it could be challenging to unclog your stormwater drain if it gets blocked. This post will show you how to unclog a clogged stormwater drain using basic equipment and methods.
Knowledge of the Drainage System
If you reside in a region that often floods, you are aware of how annoying it can be when your storm drain is clogged. In this post, we’ll outline a few easy procedures for unclogging a clogged stormwater drain.
Determine first if leaves, branches, or other debris are the cause of the obstruction. Any major obstructions in the drainage should be removed. The material should next be suctioned out of the drain using a plunger. The last step is to pour boiling water down the drain and wait until the obstruction is removed before returning the water to the ground.
Unblocking a Stormwater Drain
You may be able to unclog the blockage in your stormwater drain using a plunger or a bucket.
Use a plunger if the drain has a diameter more than 10 cm. Use a bucket if the drain has a diameter of less than 10 cm. After using the plunger or bucket, let the water a minute to run freely before trying to remove the impediment once again. Clear obstacles carefully since they could be pointy.
Tools Required
- The plunger
- Copper tube
- Measurement tape
- Carpenter’s level for joint compound
- Shaving blade
- Set of sockets Hammer
A Blocked Stormwater Drain: How to Unclog It
If your storm drain is clogged, you may need to use a plunger to remove the obstruction. To do this, position the plunger over the blockage and press and pull the plunger repeatedly until the impediment is removed. If the blockage is substantial, you should snake a copper pipe around it to clear the material. After the obstacle has been removed, mark the pipe’s length with a tape measure and trim off any extra length with a razor blade. After that, patch up any pipe fractures or holes with joint compound. Finally, ensure that the pipe is straight using a carpenter’s level, and if required, hammer the screws into place.
Utilising a hydro-jetter is an additional option. Press the button after adding water to the hydro-jetter. The nozzle releases water that clears the drain of particles.
It could be necessary to contact a specialist if none of these solutions works.
When Should a Blocked Stormwater Drain Be Unblocked?
To avoid flooding, a clogged stormwater drain should be cleared as frequently as required. All experts advise cleaning drains twice a year, although the frequency is dependent on the kind of drainage system and your circumstances.
You should clean your drainage system once a month if it is an open channel, such as a ditch or stream. You should clean your drainage system every six months if it is a sewage line or a combined sewer/stormwater drain. You should clean up any subterranean basins or catches basins in your drainage system every three years.
Tips for Cleaning Up After Unclogging a Stormwater Drain
If flooding is about to occur, clearing a clogged stormwater drain might be difficult, but it’s crucial to act fast. To make the procedure as simple as possible, use these cleaning suggestions.
- Remove any debris that could be obstructing the drain. This includes huge things like branches and leaves.
- Using a shovel or your hands, create a trench around the drain entrance.
- Push the debris towards the water until it is all gone, then place a container of water at the bottom of the trench.
- To remove the debris from the drain hole, use a plunger to suction onto it. Be careful not to snag your flesh or clothes on the sharp edges of the sewer pipe!
- To clear everything out, sweep away any leftover debris and pour hot water down the drain.
- To remove any leftover material and make sure the pipe is clear of obstacles, pour a gallon of water down the drain.
- Replace any fallen trees or branches and re-bury the earth around the drain entrance.
- For assistance with any major blockages or drainage concerns, contact a professional.
- Some Advice for Avoiding Blocked Stormwater Drains
A clogged drain is one of the most frequent reasons for drainage issues in your home or place of business. Here are some suggestions for stopping it from happening:
Regularly clear the area surrounding the drain of dirt and leaves. This will lessen the amount of obstruction that could develop.
Make sure all drains are established and maintained correctly if your property has a storm sewer system. Drainage issues at your home or place of business may result from a clogged storm sewer.
Regularly check for obstructions and clogs. Drainage issues in your house or place of business may also be brought on by a clogged septic tank.
Check the drainage system for any obstacles like pebbles or roots if you see water backing up into your house or place of business. If required, get rid of these impediments and clean the drainage system.
Call an experienced plumber like Purified Plumbing at Eastwood to have a look if you suffer drainage issues that don’t seem to be related to any of the aforementioned causes. A clogged stormwater drain may easily escalate into a major issue.
Conclusion
It’s crucial to know how to quickly clean a clogged stormwater drain if you ever find yourself in that circumstance. You can address the drainage issue and stop any more harm from occuring by following these easy measures. Don’t hesitate to get in touch with Purified Plumbing if you need assistance getting started or if you have any queries regarding unclogging a clogged stormwater drain. We’re here to assist you!
